Now that fall is officially here, it’s time to prepare your home for cold weather. These steps, most of which you can do yourself, will help cut your utility bills, protect your investment and possibly increase the value of your home.
1. Get your furnace serviced
Investing in an annual service for your home heating system will save you money in the long run. For about $100-$300, a technician will inspect your furnace, boiler or heat pump to be sure the system is clean and in good repair, and that it can achieve its manufacturer-rated efficiency. The inspection also measures carbon-monoxide leakage.
Look for a heating and air-conditioning contractor that belongs to the Air Conditioning Contractors of America and employs technicians certified by the North American Technician Excellence (NATE) program. The contractor should follow the protocol for ACCAs “national standard for residential maintenance” (or the QM, short for “quality maintenance”).
2. Reverse your ceiling fans
If your ceiling fan has a reverse switch, use it to run the fan’s blades in a clockwise direction after you turn on your heat. Energy Star says the fan will produce an updraft and push down into the room heated air from the ceiling (remember, hot air rises).
This is especially helpful in rooms with high ceilings — and it might even allow you to turn down your thermostat by a degree or two for greater energy savings.
3. Clean and Cover Patio Furniture and Your Grill
To make your life easier, use the last sunny day of the fall to wash down your patio furniture and store it away before it gets too cold.
Give your grill a thorough cleaning as well.
Once everything is nice and shiny, you can store it in your garage or shed. If you don’t have a storage space, cover your furniture with a tarp and get a cover for your grill to help protect them from the elements.
4. Do a roof inspection
Look for damaged, loose or missing shingles that may leak during winter’s storms or from melting snow. Don’t overlook cracked and worn rubber around vent pipes or masses of moss and lichen, which could indicate the roof is decaying underneath.
If need be, hire a handyman to repair a few shingles ($100 – $300 according to homeguide.com) or a roofer for a larger section ($200 – $600 for a 100-square-foot area). Check and repair breaks in the flashing seals around vent stacks and chimneys, too.
5. Caulk your windows and doors
Caulking windows and doors properly can protect your house from unwanted moisture and air leaks. If you notice drafts in your home or that your energy bills have spiked, this is a sign you might need to replace the caulk around your windows and doors. Plan to replace the caulk about once every five to 10 years.
Silicone caulk is best for exterior use because it won’t shrink and it’s impervious to the elements.
Try GE’s Silicone 2 Window and Door product, which is “rain ready” in 30 minutes. Check window-glazing putty, too (which seals glass into the window frame). Add weather stripping as needed around doors, making sure you cannot see any daylight from inside your home.
6. Clean the gutters
Gutters need to be cleaned at least twice a year — in the spring and in the fall. If you have pine trees near your home, needles will need to be removed every three months to reduce the potential for clogging the gutters and downspouts. Neglecting gutter maintenance can lead to costly repairs down the line. Regular maintenance will make your gutters last longer.
If your gutters are full of detritus, water can back up against the house and damage roofing, siding and wood trim — plus cause leaks and ice dams. Gutters filled with debris can also make homes for rodents and other pests.
7. Divert water
Add extensions to downspouts so that water should be diverted at least 4 to 6 feet away from the foundation. If a home has basement walls, it should be at least 6 feet away. The farther away from the foundation the better. Putting gravel or rocks at the end of the downspout will help avoid erosion.
For example, HomeDepot.com sells Amerimax Flex-a-Spout extension (which extends 25 to 55 inches) .
8. Turn off exterior faucets
Faucet winterization is important for preventing burst pipes. Leaving your faucet unprotected can lead to flooding and water damage in your house. Undrained water in pipes can freeze, which will cause pipes to burst as the ice expands.
4 Steps to Winterizing Outdoor Faucets
- Disconnect your hose(s). Disconnect all of your garden hoses and take off any splitters attached to your faucets. Then drain the water that remains in the faucets.
- Locate your shut-off valves. You’ll usually find shutoff valves for outdoor faucets inside your home, often on the basement wall corresponding to your outdoor faucet.
- Drain your outside faucet completely. Allow any excess water to trickle out from the faucet. If water keeps coming, you may need to tighten the interior shutoff valve. Once your faucet drains, keep the handle in the “on” position when you close things up for the winter.
- Insulate your faucet. Pick up an outdoor faucet cover for a few dollars at your local home improvement store.
If you live in a cold climate, consider having a plumber install a new freeze-proof faucet for you. This type of faucet automatically drains any water that enters when the faucet is in the “off” position to prevent a frozen buildup that can cause a pipe to burst.
9. Drain your sprinkler system
Winterizing your sprinkler system is an important part of preparing your home for cold weather. Depending on the slope of your property, you may have a choice between manual or automatic draining versus a sprinkler system blowout if you want to save some money. And if your land slopes enough to allow for complete drainage of a manual or automatic drain irrigation system, you may be able to complete winterization at no cost at all.
The average cost for a sprinkler system blowout is $100 to $250, depending on the size of the system. A sprinkler professional can perform this service on any kind of lawn sprinkler system, and it uses high-pressure air to force water out of the pipes, eliminating the problem of water sitting in low spots. Draining sprinkler-system pipes, as with spigots, will help avoid freezing and leaks.
10. Mulch leaves when you mow
Mulching leaves back into your lawn will provide a natural source of nutrients that will improve the growth of your lawn.
Mow your leaves instead of raking them, say studies at the University of Michigan and Purdue. The trick is to cut the leaves, while dry, into dime-sized pieces that will fall among the grass blades, where they will decompose and nourish your lawn over the winter.
Use your lawn mower without its bag, and optionally swap the cutting blade for a mulching blade (about $15-$35). The process may take several passes.
11. Prepare to stow your mower
There are really only two things you must do to prepare your lawn mower for hibernation. You’ll have to clean the deck and depending on the mower type, you’ll need to stabilize the fuel — or remove the battery.
Step 1: Clean the deck
The deck houses the cutting blades and facilitates the orderly expulsion of grass clippings. Not only will keeping it clean help with the performance of your mower, but it also helps cut down on the spread of lawn diseases.
Before you begin cleaning, as a safety measure disconnect the spark plug wire on gas models and remove the battery on battery-powered models. It’s always a good idea to consult your lawn mower’s product manual to assist you and maintain proper safety precautions.
Use a garden hose to spray down the deck, ensuring the water pressure is high enough to dislodge any grass clippings or debris that have adhered. Some spots may be more stubborn than others. For these hard-to-clean areas, try a brush and paint scraper.
Step 2: Winterize fuel or remove battery
As the mower sits through the winter, fuel remaining in its engine will decompose, “varnishing” the carburetor and causing difficulty when you try to start the engine in the spring.
If you keep your mower in the basement during the winter, you should remove the fuel regardless of how much is left because storing it inside could be a fire hazard.
Step 3, for a gas-powered mower: Remove or stabilize the fuel
If you’ve added a stabilizer to your fuel to keep it fresh longer, then fill the gas tank to the top with more stabilized fuel and run the engine briefly to allow it to circulate.
If not, wait until the tank is nearly empty from use and run the engine (outdoors) to use up the remaining fuel. Check your mower’s manual for other cold-weather storage steps.
Step 3, for an electric mower: Remove the battery
Remove the battery or batteries and store them inside your home to minimize temperature fluctuation. Extreme temperatures can shorten the life span of battery cells and cause them to fail prematurely.
12. Don’t prune trees or shrubs until late winter
You may be tempted to get out the pruning shears after the leaves fall, when you can first see the underlying structure of the plant. But horticulturalists advise waiting to prune until late winter for most plants, when they’ve been long dormant and just before spring growth begins. Winter is a good time for pruning and tree removal. Pruning during dormancy (called “dormant pruning”) has several benefits for your trees.
Winter pruning can avoid spreading some serious diseases that are active and spread easily during the spring and summer growing seasons. Because the tree is dormant, winter pruning doesn’t stimulate new growth. Trees are able to heal from pruning cuts before warmer weather brings out destructive insects and pathogens.
Damaged, dead or dying trees can be dangerous in prune winter, particularly when there are significant amounts of ice or snow. Dormant pruning makes them safer and can also rejuvenate weaker trees by removing dead and diseased wood.
To get advice specific to your plants and region, consult master gardeners at local nurseries or horticulturalists with your state university’s cooperation extension department. One exception: You may need to hire an arborist to remove deadfall or trim limbs close to your home or power lines that could cause problems in a winter storm.
13. Winterize your sump pump
A sump pump’s job is to move water that collects in a sump basin out of your basement and away from your home. It makes sense that a sump pump works its hardest during rainy months, when flooding is most likely to send water into basements and crawl spaces. But what about in the winter months? How does it operate when snow and ice are involved?
A sump pump still has some work to do in the winter, because all that ice and snow does eventually melt, giving the sump pump something to do. While a sump pump does run in cold weather, it shouldn’t run all the time.
One of the most important steps to winterize your sump pump is to disconnect any extension hose attached to your sump pump’s discharge pipe before the start of winter to prevent freezing. Remove your sump pump discharge hose extensions prior to the temperature dropping below freezing.
If there is a blockage of ice and the pump engages during an early thaw, or turns on to remove excess water from the sump, what may have started as a partial ice blockage will soon turn into a complete ice blockage. This could lead to a very costly spring.
14. Get the chimney swept
Before you burn the Yule log, make sure your fireplace (or any heating appliance burning gas, oil, wood or coal), chimney and vents are clean and in good repair. That will prevent chimney fires and prevent carbon monoxide from creeping into your home.
There is not a hard and firm rule on how often to clean your chimney. The National Fire Protection Association recommends having heating equipment and chimneys cleaned and inspected every year by a qualified professional.
When you burn wood in your fireplace or woodstove, it leaves behind ash and carbon residue creosote that needs to be cleaned out. Creosote is a flammable substance that can ignite into a fire that spreads throughout the chimney and to your home.
Regular cleaning of a chimney can reduce the risk of a chimney fire, but even if you choose to clean the chimney yourself, you should also have the chimney inspected by a professional on a regular basis. Professional inspection will check for creosote as well as blockage, damage and structural problems.
The job of the chimney sweep is to remove soot, blockages and built-up creosote from your chimney liner, firebox, smoke chamber and damper. This cleaning will help create a safer operation of your system during the heating system.
Search for a sweep certified by the Chimney Safety Institute of America. You can expect to pay $50 to $90 for an inspection to see if you need a cleaning, and $100 to $300 for the cleaning, according to www.costowl.com.
15. Prepare your tools for winter
Winter work can be hard on tools. Fluids can thicken and freeze, metals can shrink, and water vapor can cause cracks when it freezes and melts.
Here are four tips to keep your tools working well when the temperature drops:
- Lubricate parts of tools as the manufacturer recommends
- Store cordless power tools in a heated shed or garage, most do not do well in very cold weather
- Make sure to clean any blades or other parts of your equipment after each use. Apply a thin layer of oil to prevent rust
- Tools with metal and plastic parts can become fragile in extreme cold. Let them warm up indoors before use to prevent breakage
